Your cart is empty.
MS-130ST-M07725B-22P0+DS3-22P3-PQA 220v 130mm 2.3kw 7.7nm 2500rpm 2500ppr AC servo motor&drive kit&3m cable
- Model: MS-130ST-M07725B-22P0+DS3-22P3-P
- Shipping Weight: 15Kg
- In Stock:10
- Manufactured by: Xinje
0 reviews
| MS-130ST-M07725B-22P0+DS3-22P3-PQA 220v 130mm 2.3kw 7.7nm 2500rpm 2500ppr AC servo motor&drive kit&3m cable |
Model: MS-130ST-M07725B-22P0+DS3-22P3-PQA
Package Content:
1*Motor+Drive: MS-130ST-M07725B-22P0+DS3-22P3-PQA
1* 3M Encoder Cable &Power Cable
Product feature:
Motor feature:
- MS series servo motor
- Match DS3 series single phase 1.5~2.3kw servo drive
- Encoder is 2500 ppr
Drive feature:
1 .DS3 series contains advanced intelligent control system, can significantly resist the external disturbance and improve the system rigidity, shortening the locating time (positioning time is about 1/2 of our previous products)
- Smoother and faster speed of response: DS3 built-in state observer, the speed tracking is precision and stable, which could be restrained mechanical vibration effectively.
- Bus control system, more efficient way of communication: currently only applies to the whole series of Xinje products.
- The fastest Command refresh speed is up to 1 KHZ, through real-time communication, make the control more fast, accurate, connect more concise and convenient.
- Three kinds of control mode, the seamless switch: position control, speed control and torque control
- IO flexible configuration: 5 DI input, 3 DO output
- Input form: the symbol + pulse train, the CW + CCW pulse train, AB phase pulse
- Input frequency: open collector KPPS 200, 500 KPPS differential drive
- Interface circuit: the collector (+ 24 v level)/differential input
- Double communication port: RS232 and RS485
- Perfect protection, safe and reliable, overvoltage, undervoltage, over current, overspeed, overload, abnormal encoder and position deviation is too large.
- Built-in regenerative resistor
Specifications
1 Motor Specifications
|
Voltage level |
220V |
|
|
Motor type |
MS-130ST-M07725B-22P0 |
MS-130ST-M15015B-22P3 |
|
Rated power (KW) |
2.0 |
2.3 |
|
Rated current (A) |
7.5 |
9.5 |
|
Rated speed (rpm) |
2500 |
1500 |
|
Rated torque (N·m) |
7.7 |
15 |
|
Peak torque (N·m) |
22 |
30 |
|
Back EMF constant (V/krpm) |
68 |
114 |
|
Torque coefficient (N·m/A) |
1.03 |
1.58 |
|
Rotor inertia (Kg·m2) |
1.53×10-3 |
2.77×10-3 |
|
Winding resistor (Ω) |
1.01 |
1.1 |
|
Winding inductance (mH) |
2.94 |
4.45 |
|
Electrical time constant (ms) |
3.8 |
4.05 |
|
Weight (Kg) |
10 |
14.4 |
|
Encoder ppr (PPR) |
2500 |
|
|
Pole pairs |
4 |
|
|
Motor insulation level |
Class B (130centigrade degree) |
|
|
Protection level |
IP65 |
|
|
Ambient temperature |
-20~50centigrade degree |
|
|
Ambient humidity |
Related humidity <90% (no condensation) |
|
2 Drive Specifications
|
Voltage |
220V |
|||
|
Servo drive model DS3- |
DS3-22P3-PQA |
|||
|
The matching motor MS- |
130ST-M07725-22P0 |
|||
|
power kW |
2.3 |
|||
|
General specification |
Input power |
Single / three phase AC220V ±10 50/60Hz |
||
|
Feedback |
Increment-type 2500 ppr |
|||
|
Using temperature |
0 ~+50 / -20 ~+ 85 centigrade degree |
|||
|
Using humidity |
Below 90% RH (no condensation) |
|||
|
Vibration /impact resistance |
4.9m/s2/ 19.6m/s2 |
|||
|
Control mode |
Speed/torque control |
Load change rate |
0~100% load: ±below 0.01%(rated speed) |
|
|
Voltage change rate |
Rated voltage ±10%:0%(rated speed) |
|||
|
Frequency feature |
250HZ(JL≤JM) |
|||
|
Soft start time |
0~65535ms (set acceleration, deceleration individually) |
|||
|
Input/output signal |
Encoder feedback output |
Differential mode output (ABZ phase) |
||
|
Input signal |
External input:5 Changeable signa distribution: /S-ON, /P-CON, /P-OT, /N-OT, /ALM-RST, /PCL, /NCL, /SPD-D, /SPD-A, /SPD-B, /C-SEL, /ZCLAMP, /CLR, /G-SEL |
|||
|
Output signal |
External output:3 /ALM |
|||
|
Function |
Regeneration frequency |
DS3-21P5-PQA/ DS3-22P3-PQA:2.5 s/min DS3-20P2-PQA~DS3-20P7-PQA:1.6 s/min |
||
|
Dynamic brake (DB) |
None |
|||
|
Regeneration |
Built-in regenerative resistor |
|||
|
Protection |
overvoltage, undervoltage, regeneration error, overtemperature, overcurrent, overspeed, analog input error, position offset overflow, output shorting, current error, encoder cut, encoder error, overload, power off when running, write parameter error… |
|||
|
LED display |
Charge, power supply, 7-segment LED ×5 (built-in digital operate) |
|||
|
Communication function |
COM 1 |
RS232, connect to PC |
||
|
COM 2 |
RS232, RS485, connect to PLC, HMI, PC and other devices Serial parameter can be set; communication protocol: ModbusRTU slave; Modbus station No. can be set State display, user constant setting, monitor display, alarm display, alarm display, special control, online debug |
|||
|
Install way |
mounting base |
|||
There are currently no product reviews.
