LC3722HTC 3ph NEMA34 NEMA42 NEMA52 Stepper Motor Driver 110-220VAC 7A

  • Model: LC3722HTC
  • Shipping Weight: 1Kg
  • In Stock:20
  • Manufactured by: LiChuan
Qty:          Favorite

Payment method Shipping method Contact us


0 reviews


3ph NEMA34 NEMA42 NEMA52 Stepper Motor Driver 110-220VAC 7A

LC3722HTC Three-phase hybrid stepping motor drive

LC3722HTC is a kind of three-phase hybrid stepping motor drive based on DSP control , it is a new generation of digital stepper motor drive made up of  the advanced DSP control chip and three-phase inverter driver module combine together.The drive voltage is AC110V - 220 v, adaptive current is below 7.0 A,57-130 mm external diameter of the various types of three-phase hybrid stepping motor. The inner of drive adopts a circuit similar with servo control principle.the circuit can make the motor run smoothly, little vibration and noise.When motor is in high speed, the torque is much higher than the two and five phase hybrid stepping motors.Step positioning accuracy up to 60000 / rolls. The products are widely used in engraving machine, medium-sized nc machine, computer embroidery machine, packaging machinery and other high resolution of large and medium-sized CNC equipment.

Features:

·High performance and low price
·Equipped with 16 files of uniform angle constant torque subdivided ,the   max resolution is 60000 steps/roll
·The highest response frequency up to 200 KPPS
·when step pulse stops for more than 1.5 S, coil current will be  reduced
  to half of the rated current automatically

·Photoelectric isolation, signal input/output
·Drive current 1.3A/phase to 7.0 A/phase ,16 files is adjustable
·Single power input, the voltage range: AC110V - 220 v

·Phase memory function (note: when stop inputting for more than 3 seconds, drive will bear motor phase in mind automatically  at the time, back to electricity or WF signals from low level to high , drive will  recovery motor phase automatically)

current setting

Drive working current is set by the D1 - D4 terminals, running current set switch for normal work output current  (see table below)

running current

DV3722

1.3

1.6

2.1

2.3

2.5

3.0

3.2

3.5

D1

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

D2

OFF

OFF

OFF

OFF

ON

ON

ON

ON

D3

OFF

OFF

ON

ON

OFF

OFF

ON

ON

D4

OFF

ON

OFF

ON

OFF

ON

OFF

ON

running current

DV3722

4.0

4.5

5.0

5.3

5.8

6.2

6.6

7.0

D1

ON

ON

ON

ON

ON

ON

ON

ON

D2

OFF

OFF

OFF

OFF

ON

ON

ON

ON

D3

OFF

OFF

ON

ON

OFF

OFF

ON

ON

D4

OFF

ON

OFF

ON

OFF

ON

OFF

ON

Segment setting

Drive subdivided is set by D5 - D8 terminals , 16 files in total, D9 and D10 are for functionality setting. Schedule such as: division number(pulse/roll)

Division number

400

500

600

800

1000

1200

2000

3000

D5

ON

ON

ON

ON

ON

ON

ON

ON

D6

ON

ON

ON

ON

OFF

OFF

OFF

OFF

D7

ON

ON

OFF

OFF

ON

ON

OFF

OFF

D8

ON

OFF

ON

OFF

ON

OFF

ON

OFF

Division number

4000

5000

6000

10000

12000

20000

30000

60000

D5

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

D6

ON

ON

ON

ON

OFF

OFF

OFF

OFF

D7

ON

ON

OFF

OFF

ON

ON

OFF

OFF

D8

ON

OFF

ON

OFF

ON

OFF

ON

OFF

D9

ON,Double pulse:  PU is forward direction step pulse signal,

               DR is reverse direction  step pulse signal

OFF,Single pulse: PU is step pulse signal, DR is direction control signals

D10

Automatic detection switch

(when OFF receiving external pulse, when ON runs at a speed of 30 r/min in internal drive)

 

Note: Custom division number according to customers’ request.

Drive wiring/size sketch map

LK(G}_X`EHT{S7$M7E$J01X

Note:

1, The input voltage cannot exceed ac 220V;

 2, The input control signal level  is 5v,current limiting resistor is required when   higher than 5 v

3, Falling edge is effective when inputting pulse signal ;

4, Drive will stop working when temperature over 80 degrees , failure indicator light ALM on , until the drive temperature drops to 50 degrees, the driver needs to be on the electricity can be restored. Overheating protection with radiator, please.

5,Over current (load short out) fault indicator light ALM on, please check the     motor wiring and other short out fault, it needs to electrified again to recover after ruling out.

 6, No motor fault indicator ALM on, please check the motor connection, it needs to electrified again to recover after ruling out.

Pin function statement

Port

definitions

Connector

 pins no.

mark symbol

Function

Annotation

 

 

 

 

 

 

 

 

 

 

 

 

DB 15

1

5PU+

input signal photoelectric isolation plus port

connect + 5 v power supply,  + 5 v to + 24 v can all be driven, higher than + 5 v, current limiting resistor is required

2

PU-

DP9=OFF,PU is stepping pulse signal

 

 Falling edge effective, when the pulse  change from high to low,the motor takes a step. input resistance 220ohm, requirement: low level 0-0.5 V, high level 4-5 V, pulse width > 2.5 mu s

DP9=ON,PU Is plus direction stepping pulse signal

3

5DR+

input signal photoelectric isolation plus port

connect + 5 v power supply,  + 5 v to + 24 v can all be driven, higher than + 5 v, current limiting resistor is required

4

DR-

DP9=OFF,DR is direction control signal

Used to change the motor turning.input resistance 220ohm, requirements: low level 0-0.5 V, high level 4-5 V, pulse width > 2.5 mu s

DP9=ON,DR is reverse direction       stepping  pulse signal

7

5MF+

input signal photoelectric isolation plus port

connect + 5 v power supply,  + 5 v to + 24 v can all be driven, higher than + 5 v, current limiting resistor is required

8

MF-

motor release signal

Shut off the motor terminal current when effective (low level) , drive stop working, the motor in the free state.

9

ALM+

Drive failure output signal photoelectric isolation plus port

when over-current, overheating fault appear, drive output the trouble signal, it is effective (high level)

10

ALM-

Drive failure output signal photoelectric isolation minus port

 

11

RDY+

drive ready to output signal of photoelectric isolation plus port

Driver’s status is normal, when ready to accept the signal of Controller,it is effective (low level)

12

RDY-

drive ready to output signal of photoelectric isolation minus port

 

13

24PU+

input signal photoelectric isolation plus port

·          +24V drivable

 

14

24DR+

input signal photoelectric isolation plus port

+24V drivable

15

24MF+

input signal photoelectric isolation plus port

+24V drivable

 

12

LN

  power supply

power supply:AC110-220V

3

PE

base line

Ground(Inscribe shell of drive)

4

U

 

8}E]2NPB`GV}F93$D$_UTCY

5

V

motor wiring

6

W

 

 

 

There are currently no product reviews.

1 2 3 4 5
Five Stars
NOTE: HTML tags are not allowed.
NOTE: Reviews require prior approval before they will be displayed