Your cart is empty.
3M2080 3phase NEMA42 NEMA52 stepper motor driver controller amplifier AC80-220V 2.2-8.5A
- Model: 3M2080
- Shipping Weight: 2Kg
- In Stock:50
0 reviews
Model: 3M2080
Name: 3M2080 JMC stepper motor driver
Detailed information:
performance index:
3M2080 a such angle constant torque micro stepping driver, drive AC voltage 80V-220VAC, suitable with current below the 6.6A. Outside 86-130MM types of three-phase hybrid stepping motor. The driver uses a similar servo control principle of the circuit, this circuit can make the motor running smoothly, almost no vibration and noise. Due to the high operating voltage of the driver, the torque of the motor at high speed is much higher than that of the other three-phase, five phase hybrid and traditional stepping motor. Step pulse stop over 100m/s. Drive current automatically halved. The positioning accuracy is up to 12800 steps / turn.
features:
1:80-220V AC power supply, to adapt to the worst grid environment; H bridge bipolar constant phase flow subdivision drive;
2: the original speed adaptive circuit, automatic optimization; subdivision of the current set of convenience; 1-64 subdivision of 16 operating modes
3: over current, over voltage, under voltage, over temperature, short circuit protection; off line (ENA) protection function.
Electrical index Environmental indicator
|
Instructions |
Min |
Typical |
Max |
|
cooling |
Natural cooling or forced cooling |
|
|
voltage(VAC) |
80V |
110VAC |
220V |
Use environment |
occasion |
Avoid dust, oil mist and corrosive gases. |
|
|
Working current(A) |
1.7A |
----- |
6.6A |
Storage temperature |
-10·C~80·C |
||
|
Logic input current (mA) |
|
15 |
|
Maximum ambient temperature |
-10·C~65·C |
||
|
Step pulse rate (KHZ) |
---- |
---- |
200 |
Ambient humidity |
Not dew, not water |
||
|
Pulse low time (US) |
2.5 |
---- |
---- |
Vibration |
|
5.9m/s2Max |
|
|
|
|
|
|
weight |
|
1.8Kg |
|
interface functions
P1 input signal interface description
|
symbol |
function |
description |
|
PLS+ |
Input signal photoelectric isolation positive end |
Connected to the +5V power supply, +5V~+24V can be driven, higher than the +5V to be connected to the current limiting resistance |
|
PLS- |
Step pulse signal |
Down along the effective, whenever the pulse from high to low when the motor to take a step. Input resistance 220 ohm, requirements: low level 0~0.5V, high level 4~5V, pulse width >2.5uS. |
|
DIR+ |
Input signal photoelectric isolation positive end |
Connected to the +5V power supply, +5V~+24V can be driven, higher than the +5V to be connected to the current limiting resistance |
|
DIR- |
Direction control signal |
Used to change the steering of a motor. Input resistance 220 ohm, requirements: low level 0~0.5V, high level 4~5V, pulse width >2.5uS. |
|
ENA+ |
Input signal photoelectric isolation positive end |
Connected to the +5V power supply, +5V~+24V can be driven, higher than the +5V to be connected to the current limiting resistance |
|
ENA- |
Motor release signal |
Active (low level) when turn off the motor coil current, the drive stops working, the motor is in a free state. |
|
phase |
Model |
Current(A) |
Voltage(V) |
micorsteps |
For motor |
weight(kg) |
size(mm) |
Control signal |
|
2phase |
2M415 |
0.21-1.5A |
DC(24-36V) |
2-64 |
35.42 |
0.2 |
86*55*20 |
single |
|
2M420 |
0.3-2.5A |
DC(24-48V) |
2-128.5-125 |
42.57 |
0.2 |
118*75.5*33 |
single |
|
|
2M542-N |
1.0-4.2A |
DC(24-48V) |
2-128.5-125 |
57.86 |
0.27 |
118*75.5*34 |
differential |
|
|
2M656 |
1.3-5.6A |
DC(24-48V) |
1-64.2.5-50 |
57.86 |
0.27 |
118*75.5*34 |
differential |
|
|
2M982 |
1.8-7.8 |
DC(30-80V) |
1-64.2.5-50 |
57.86 |
0.57 |
150*97.5*48 |
differential |
|
|
2MA860H |
2.5-6A |
AC(50-80V) |
1-64.2.5-50 |
57.86.110 |
0.6 |
150-97.5*53 |
differential |
|
|
MA960H |
2.5-6A |
AC(50-80V) |
2-64 |
57.86.110 |
0.6 |
150*97.5*53 |
differential |
|
|
2M2260 |
2.5-6A |
AC(80-220V) |
1-64.2.5-50 |
86.110.130 |
1.5 |
198*104*86 |
differential |
|
|
2M2280 |
2.2-8.5A |
AC(80-220V) |
1-64.2.5-50 |
110.130 |
1.8 |
198*136.5*88 |
differential |
|
|
|
3M660 |
1.3-5.8A |
DC(24-48V) |
1-64.2.5-50 |
57.86 |
0.27 |
118*75.5*34 |
differential |
|
3M860 |
2.0-8.3A |
DC(24-80V) |
1-64.2.5-50 |
57.86 |
0.57 |
150*97*48 |
differential |
|
|
3M2060H |
1.3-5.6A |
AC(80-220V) |
1-64.2.5-50 |
86.110.130 |
1.5 |
198*104*86 |
differential |
|
|
3M2080 |
2.2-8.5A |
AC(80-220) |
1-64.2.5-50 |
110.130 |
1.5 |
198*136.5*88 |
differential |
There are currently no product reviews.
